Sherman_Hi_Lo_Transmission_10_SPLINE_Ford_Tractor_8N_9N_2N_Jubilee_Naa_600_01_xl

Sherman Hi Lo Transmission 10 SPLINE Ford Tractor 8N 9N 2N Jubilee Naa 600

Date: October 30, 2021 Posted by: admin In: sherman

Sherman Hi Lo Transmission 10 SPLINE Ford Tractor 8N 9N 2N Jubilee Naa 600
Sherman Hi Lo Transmission 10 SPLINE Ford Tractor 8N 9N 2N Jubilee Naa 600
Sherman Hi Lo Transmission 10 SPLINE Ford Tractor 8N 9N 2N Jubilee Naa 600
Sherman Hi Lo Transmission 10 SPLINE Ford Tractor 8N 9N 2N Jubilee Naa 600
Sherman Hi Lo Transmission 10 SPLINE Ford Tractor 8N 9N 2N Jubilee Naa 600
Sherman Hi Lo Transmission 10 SPLINE Ford Tractor 8N 9N 2N Jubilee Naa 600
Sherman Hi Lo Transmission 10 SPLINE Ford Tractor 8N 9N 2N Jubilee Naa 600

Sherman Hi Lo Transmission 10 SPLINE Ford Tractor 8N 9N 2N Jubilee Naa 600
ALL GEARS HAVE ALL BEEN INSPECTED AND IN GREAT SHAPE. THE BACKING PLATE AND SHIFTER HANDLE ARE INCLUDED. THIS UNIT WAS CLEANED AND PAINTED AFTER BEING INSPECTED. ONLY WORKS WITH 10 SPLINE CLUTCH. NO CRACKS OR WELDS. NO WORN OUT TEETH OR MISSING TEETH. THIS SHIFTER WORKS AS IT SHOULD WITH NO KNOWN ISSUES. What is the Combination Transmission? The Sherman step-up/step-down combination transmission is, by far, the most popular and most useful transmission back then and still today. Steering wheel information plate. The Sherman combination transmission shifter. Split the tractor between the engine and transmission. Once separated, remove the left brake pedal and the brake cross shaft. Use the diagram below to locate the spot to drill the shifter hole. The measurements should get the hole location within 1/8 or closer of where it should be. You may want to use a hole saw to cut a 1 hole first and then true up the location later by opening the hole to 1-1/4 with a die grinder. Emove the tractor transmission input shaft and tube. Remove the front input shaft and support tube from the Sherman. Also remove and set aside the thrust washer and bearing that go between the input shaft and the output shaft. Remove the Sherman rear mounting plate and gasket. Bolt the Sherman rear mounting plate to the tractor transmission using at least 2 shims and one paper gasket. You will need a 5/16 Allen wrench or socket to tighten the bolts. Put the Sherman in place with the gasket on the rear mounting plate and start tightening the 4 mounting bolts. Turn the main shaft inside by hand and note the effort to rotate it (tractor transmission should be in neutral). As you continue to tighten the 4 bolts to pull the Sherman housing up to the mounting plate, keep turning the shaft and check for sideways play and end play. The bearing load is correct when a very slight increase is noted in the effort required to turn the input shaft and very little play can be felt sideways. Add or remove shims until you have the correct preload. Do not load too tight! Too loose is better than too tight. Once you have determined the correct number of shims needed (if any) pull the Sherman back out and apply Permatex #2 sealer to the rear mating surfaces of the Sherman and the mounting plate and reinstall it. Replace the thrust washer and needle bearing on the front end of the output shaft end and pour 2 pints of gear lube into the Sherman housing. Dont skip this step! It needs to be full of gear lube before use. Install the Sherman input shaft and support tube back onto the transmission housing (use Permatex on this gasket also). True up the shifter hole if necessary. Bolt on the shifter. Turn the input shaft of the Sherman to be sure its free. While still turning the input shaft, shift the Sherman through its 3 gear positions to verify it is shifting correctly. Re-install the brake cross shaft, and reassemble the tractor. If additional metal shims are needed to get the correct preload they are available from Ford/New Holland dealers as part numbers: C3NN7135A. 012 9N7086 paper gasket. The item “Sherman Hi Lo Transmission 10 SPLINE Ford Tractor 8N 9N 2N Jubilee Naa 600″ is in sale since Saturday, October 30, 2021. This item is in the category “Business & Industrial\Heavy Equipment, Parts & Attachments\Heavy Equipment Parts & Accessories\Antique & Vintage Equipment Parts”. The seller is “lrypbuys” and is located in Willoughby, Ohio. This item can be shipped to United States.
  • Model: Tractor 8N 9N 2N Jubilee Naa 600
  • Modified Item: No
  • Country/Region of Manufacture: United States
  • Custom Bundle: No
  • Compatible Equipment Make: International
  • Model Year: Unknown
  • Part Type: Transmission
  • Brand: Ford
  • Compatible Equipment Type: International Tractor

Sherman Hi Lo Transmission 10 SPLINE Ford Tractor 8N 9N 2N Jubilee Naa 600

Comments are currently closed.

Recent Posts

Archives

Categories